The James Instruments Gecor 8 Basic System, is used for analyzing corrosion of concrete reinforcing steel in existing structures.

• Cu/CuSO4 only
• Rapid mapping capabilities for analysis of large structures
• Advanced method for more accurate corrosion rate determination
• New sensor design for analysis of wet or submerged structures
• New method for analysis of cathodic protection systems while the system is running

The James Instruments Gecor 8 Complete System, is used for analyzing corrosion of concrete reinforcing steel in existing structures.

• Cu/CuSO4 Half-Cells
• Rapid mapping capabilities for analysis of large structures
• Advanced method for more accurate corrosion rate determination
• New sensor design for analysis of wet or submerged structures
• New method for analysis of cathodic protection systems while the system is running

The James Instruments ASR-Detect Alkalai Silica Reaction Test, is used to determine the presence of alkilai-silica reactive gel in hardened concrete.

• Minimal operator training and no special equipment required
• Results obtained in less than five minutes are easy to interpret
• Test can be carried out completely on site
• Utilizes only two environmentally safe dyes
• Identifies ASR in concrete and differentiates ASR from other causes of degradation

The James Instruments Carbo Detect System Carbonation Test, is used to determine the presence of carbonation on concrete samples.

• Gives depth of carbonation
• Results obtained in less than five minutes are easy to interpret
• Test can be carried out completely on site
• Results obtained in less than five minutes are easy to interpret
• Economic, fast and easy to use

The James Instruments Mini R-Meter System, is an economical hand held unit used for finding the location, estimates either depth, or size of reinforced rebar, post tension cables, copper and conduit

• Rebar Locating Detection and Orientation
• Single sensor for all depth ranges
• Locates up to 8" (200 mm)
• Eddy current design for greater accuracy

The James Instruments Mini R-Meter System w/ Software, is an economical hand held unit used for finding the location, estimates either depth, or size of reinforced rebar, post tension cables, copper and conduit

• Rebar Locating Detection and Orientation
• Single sensor for all depth ranges
• Locates up to 8" (200 mm)
• Eddy current design for greater accuracy

The James Instruments Ohmcorr Complete System, is a resistivity meter used to assess corrosion currents in concrete.

• Assesses damaging corrosion currents in concrete
• Economic and easy to use
• Direct digital readout of resistivity
• Used in conjunction with CorMap System to produce resistivity plots

The James Instruments Porosiscope, is used to determine air and water permeability in concrete both at and below the surface.

• Measure air and water permeability
• Permeability on concrete surface and within the concrete
• Porosity in sealants and surface mortars can be checked
• Non-destructive (only a small plugged hole is required)

The James Instruments Porosiscope Plus, is used to determine air and water permeability in concrete both at and below the surface.

• Measure air and water permeability
• Permeability on concrete surface and within the concrete
• Porosity in sealants and surface mortars can be checked
• Non-destructive (only a small plugged hole is required)
• Includes Surface Chamber

The James Instruments Pull Test, is used to measure the bond strength or tensile strength of concrete, asphalt, tile, concrete repair, or other overlay material by the direct tension or pull off method.

• Accurate bond strength of repair mortars, epoxy resins, laminates, overlays, and other coatings
• Calibrated gauge with maximum load indicator and mechanical damping
• Ball Joint Design for rapid testing as well as assuring direct tensile loading
• Adjustable alignment plate with built in leveling facility for both vertical and horizontal pulls

The James Instruments Rebarscope Basic System, utilizes the latest in eddy current sensing and microprocessor technology to accurately locate, determine depth, and estimate diameter of metal objects in structures.

• Locates rebar, post tension cable, conduit, and copper pipe
• Rugged and splash resistant case daylight visible display
• Locates up to 8" (200 mm) deep
• Determines bar size up to 45" (115 mm) deep
• Single sensor for all depth ranges

The James Instruments Rebarscope Basic System w/ Rebarlinx Software, utilizes the latest in eddy current sensing and microprocessor technology to accurately locate, determine depth, and estimate diameter of metal objects in structures. Includes basic unit and basic software.

• Locates rebar, post tension cable, conduit, and copper pipe
• Rugged and splash resistant case daylight visible display
• Locates up to 8" (200 mm) deep
• Determines bar size up to 45" (115 mm) deep
• Includes Basic System and Rebarlinx Software