Enclosure Accessories

Integra DIN6-IMP is a set of 35mm slotted DIN rail, pre-cut to a length of 4.5" and includes mounting screws. The pre-cut size is designed to mount within all 6" wide Integra polycarbonate enclosures.

• Dims: 4.5 x 1.39 x 0.28" long
• Slotted top hat DIN rail design
• Steel Design
• Sold as set of two

Integra DIN5-IMP is a set of 35mm slotted DIN rail, pre-cut to a length of 4.88" and includes mounting screws. The pre-cut size is designed to mount within all 5" wide Integra polycarbonate enclosures.

• Dims: 4.88 x 1.39 x 0.28" long
• Slotted top hat DIN rail design
• Steel Design
• Sold as set of two

Integra DIN6 is a set of 35mm slotted DIN rail, pre-cut to a length of 4.88" and includes mounting screws. The pre-cut size is designed to mount within all 6" wide Integra polycarbonate enclosures.

• Dims: 4.88 x 1.39 x 0.28" long
• Slotted top hat DIN rail design
• Steel Design
• Sold as set of two

Integra DIN8 is a set of 35mm slotted DIN rail, pre-cut to a length of 6.75" and includes mounting screws. The pre-cut size is designed to mount within all 8" wide Integra polycarbonate enclosures.

• Dims: 6.75 x 1.39 x 0.28" long
• Slotted top hat DIN rail design
• Steel Design
• Sold as set of two

Integra DIN8-IMP is a set of 35mm slotted DIN rail, pre-cut to a length of 6.75" and includes mounting screws. The pre-cut size is designed to mount within all 8" wide Integra polycarbonate enclosures.

• Dims: 6.75 x 1.39 x 0.28" long
• Slotted top hat DIN rail design
• Steel Design
• Sold as set of two

Integra DIN10 is a set of 35mm slotted DIN rail, pre-cut to a length of 8.75" and includes mounting screws. The pre-cut size is designed to mount within all 10" wide Integra polycarbonate enclosures.

• Dims: 35mm x 7mm x 8.75" long
• Slotted top hat DIN rail design
• Steel Design
• Sold as set of two

The Altelix DRS-NS08 is a 35mm slotted DIN rail, pre-cut to a length of 6.2" and includes mounting screws.

• 6.2" Length
• Slotted top hat 35mm DIN rail design
• 20 Gauge Steel

The Hammond 1418WFHP panel rails provides Hammond 72x24" enclosures with 19 or 24" rack mounting capability.

• 35U
• 10 Gauge Steel, Powder Coated White
• Drilled and tapped 10-32 to EIA spacing of 0.5" - 0.63" - 0.63" - 0.5".

The Hammond 1550WD is a rugged diecast aluminum enclosure finished in a natural vibra finish for a smooth surface with no sharp edges. Includes stainless steel philips head machine screws used to secure lid into factory tapped holes. The enclosure is designed to meet IP66 when the included water tight gasket is installed.

• IP66 Rated
• IP66 Gasket Included
• Lift-Off Door
• Natural Finish

The Allied Moulded AMHS400 is designed to seal unused holes in your enclosures such as push­button, conduit and knock­out holes while maintaining applicable NEMA/UL/CSA enclosure ratings.

• Hole Dia. Range: 4.500-4.750"
• Trade Size: 4.641
• RAL 7035 Light Gray Polycarbonate

The Allied Moulded AMHS400-GY is designed to seal unused holes in your enclosures such as push­button, conduit and knock­out holes while maintaining applicable NEMA/UL/CSA enclosure ratings.

• Hole Dia. Range: 4.500-4.750"
• Trade Size: 4.641
• ANSI 61 Dark Gray Polycarbonate

The Hammond 1427NCG series liquid-tight cable glands are used to seal cable entries, keep contaminants from entering enclosures, provide strain relief and thus reduce stress on components and termination points inside enclosures.

• Single Unit
• Clamping Range: 4 to 8 mm
• Rating: IP68
• Color: Black
• Standards: UL, RoHS