Enclosure Thermal Management

The Stego MFR 012 series hygrostat is designed to control the relative humidity inside enclosures. When connected to an enclosure heater (dehumidifier), it will energize the heater at the humidity set point in order to raise the dew point. This helps prevent damage and malfunction of electronic components caused by condensation and corrosion.

• Mechanical Adjustable Hygrostat
• Humidity Setting: 35-95% RH
• Mounting: DIN Rail

The FZK 011 mechanical thermostat is used for controlling heating and cooling equipment, filter fans or signal devices where a higher degree of sensing accuracy is required. The thermostat registers the surrounding air and can switch both inductive and resistive loads via snap-action contact.

• AdjustableThermostat
• Setting Range (NC): 40-140 F
  Setting Range (NO): 40-140 F

The FZK 011 mechanical thermostat is used for controlling heating and cooling equipment, filter fans or signal devices where a higher degree of sensing accuracy is required. The thermostat registers the surrounding air and can switch both inductive and resistive loads via snap-action contact.

• AdjustableThermostat
• Setting Range (NC): 5-60 C
  Setting Range (NO): 5-60 C

The FZK 011 mechanical thermostat is used for controlling heating and cooling equipment, filter fans or signal devices where a higher degree of sensing accuracy is required. The thermostat registers the surrounding air and can switch both inductive and resistive loads via snap-action contact.

• AdjustableThermostat
• Setting Range (NC): 5-60 C
  Setting Range (NO): 5-60 C

The Saginaw Type 12 series has an easy to install snap fit design for use on air discharge side of fan package for NEMA 1 and 12 applications. Housing and grille are made of black heat resistant (ABS-FR), self-extinguishing material.

• System of protection NEMA Type 12
• Cut-out dimensions: 11.57 x 11.57"
• Color: Black

The Saginaw Type 12 series has an easy to install snap fit design for use on air discharge side of fan package for NEMA 1 and 12 applications. Housing and grille are made of light gray heat resistant (ABS-FR), self-extinguishing material.

• System of protection NEMA Type 12
• Cut-out dimensions: 11.57 x 11.57"
• Color: Light Gray

The Saginaw Type 3R series has an easy to install snap fit design for use on air discharge side of fan package in NEMA 3R applications.

• System of protection NEMA Type 3R
• Cut-out dimensions: 11.57 x 11.57"
• Color: Black

The Saginaw Type 12 series has an easy to install snap fit design for use on air discharge side of fan package for NEMA 1 and 12 applications. Housing and grille are made of black heat resistant (ABS-FR), self-extinguishing material.

• System of protection NEMA Type 12
• Cut-out dimensions: 3.75 x 3.75"
• Color: Black

The Saginaw Type 3R series has an easy to install snap fit design for use on air discharge side of fan package in NEMA 3R applications.

• System of protection NEMA Type 3R
• Cut-out dimensions: 3.75 x 3.75"
• Color: Black

The Saginaw Type 12 series has an easy to install snap fit design for use on air discharge side of fan package for NEMA 1 and 12 applications. Housing and grille are made of black heat resistant (ABS-FR), self-extinguishing material.

• System of protection NEMA Type 12
• Cut-out dimensions: 5.03 x 5.03"
• Color: Black

The Saginaw Type 3R series has an easy to install snap fit design for use on air discharge side of fan package in NEMA 3R applications.

• System of protection NEMA Type 3R
• Cut-out dimensions: 5.03 x 5.03"
• Color: Black

The Saginaw Type 12 series has an easy to install snap fit design for use on air discharge side of fan package for NEMA 1 and 12 applications. Housing and grille are made of black heat resistant (ABS-FR), self-extinguishing material.

• System of protection NEMA Type 12
• Cut-out dimensions: 8.91 x 8.91"
• Color: Black