The Stego 28401.0-00 is designed to provide a protected enclosure environment for valuable and crucial components with an IP66 rated degree of protection. A waterproof membrane inside the device allows air and humidity to leave the enclosure while not allowing moisture and dust from the outside to enter.

• IP66 Protection
• Sold Individually
• Air Permeability 1200 liters/hr
• 303 Stainless Steel

The HGK 047 heaters are used in enclosures to maintain minimum operating temperatures and to help prevent failure of electronic components caused by condensation and corrosion.

• DIN Mounting
• I (grounded) / IP44
• UL File No. E234324, EAC

These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature must be maintained above a minimum value.

• DIN Mounting
• I (grounded) / IP20
• UL File No. E150057, VDE, EAC

The HGK 047 heaters are used in enclosures to maintain minimum operating temperatures and to help prevent failure of electronic components caused by condensation and corrosion.

• DIN Mounting
• I (grounded) / IP44
• VDE, EAC

The Stego FPI 018 series are used to provide cooling by forced air-circulation in enclosures and cabinets containing eletrical/electronic and other components. The interior temperature of an enclosure can be reduced by channelling cooler, filtered outside air into the enclosure, thus expelling hot inside air.

• FPI - Airflow direction in
• New air-flap outlet technology for high airflow
• Single filter mat system design
• Easy mounting

The Stego FPI 018 series are used to provide cooling by forced air-circulation in enclosures and cabinets containing eletrical/electronic and other components. The interior temperature of an enclosure can be reduced by channelling cooler, filtered outside air into the enclosure, thus expelling hot inside air.

• FPI - Airflow direction in
• New air-flap outlet technology for high airflow
• Single filter mat system design
• Easy mounting

The Stego FPO 018 series are used to provide cooling by forced air-circulation in enclosures and cabinets containing eletrical/electronic and other components. The Filter Fan Plus draws the heated air from the enclosure to the outside. Cooler outside air enters the enclosure via the intake filter.

• FPO - Airflow direction out
• New air-flap outlet technology for high airflow
• Single filter mat system design
• Easy mounting

The Stego 28401.0-02 is designed to provide a protected enclosure environment for valuable and crucial components with an IP66 rated degree of protection. A waterproof membrane inside the device allows air and humidity to leave the enclosure while not allowing moisture and dust from the outside to enter.

• IP66 Protection
• Sold Individually
• Air Permeability 1200 liters/hr
• 316 Stainless Steel

The Stego FF 018 series are used to provide an optimum climate in enclosures. The interior temperature of an enclosure can be reduced by channeling cooler filtered outside air into the enclosure thus expelling heated internal air. The resulting air flow prevents formation of localized heat pockets and protects the electronic components from overheating.

• Direction of air flow can be switched
• Intake and exhaust hoods prevent direct infiltration
• Self-adhesive seal
• Air channeling allows for quiet operation

The Stego FF 018 series are used to provide an optimum climate in enclosures. The interior temperature of an enclosure can be reduced by channeling cooler filtered outside air into the enclosure thus expelling heated internal air. The resulting air flow prevents formation of localized heat pockets and protects the electronic components from overheating.

• Intake and exhaust hoods prevent direct infiltration
• High air volume
• Time-saving installation
• UV resistant plastic

The Stego RFP 018 series are used in enclosures from which warm air must be diverted due to increased heat development. The ready-to-connect and low-noise roof filter fan is used to expel warm air from within the enclosure. Alternatively, the roof exhaust filter provides passive ventilation.

• Minimal mounting depth
• Very low noise
• High air volume
• Time-saving installation and mat exchange

The Stego FPO 018 series are used to provide cooling by forced air-circulation in enclosures and cabinets containing eletrical/electronic and other components. The Filter Fan Plus draws the heated air from the enclosure to the outside. Cooler outside air enters the enclosure via the intake filter.

• FPO - Airflow direction out
• New air-flap outlet technology for high airflow
• Single filter mat system design
• Easy mounting